Search results for " Test blanket module"
showing 5 items of 5 documents
Updated design and integration of the ancillary circuits for the European Test Blanket Systems
2019
The validation of the key technologies relevant for a DEMO Breeding Blanket is one of the main objectives of the design and operation of the Test Blanket Systems (TBS) in ITER. In compliance with the main features and technical requirements of the parent breeding blanket concepts, the European TBM Project is developing the HCLL (Helium Cooled Lithium Lead) and HCPB (Helium Cooled Pebble Bed)-TBS, focusing in this phase on the design life cycle and on R&D activities in support of the design. The TBS ancillary systems are mainly circuits devoted to the removal of thermal power and to the extraction and recovery of the tritium generated in the Test Blanket Modules. They are: • The Helium C…
Study of the helium-cooled lithium lead test blanket module nuclear behaviour under irradiation in ITER
2009
Abstract The present paper deals with the detailed investigation of the helium-cooled lithium lead test blanket module (HCLL-TBM) nuclear behaviour under irradiation in ITER, carried out at the Department of Nuclear Engineering of the University of Palermo adopting a numerical approach based on the Monte Carlo method. A realistic 3D heterogeneous model of the HCLL-TBM was set-up and inserted into an ITER 3D semi-heterogeneous model that realistically simulates the reactor lay-out up to the cryostat. A Gaussian-shaped neutron source was adopted for the calculations. The main features of the HCLL-TBM nuclear response were assessed, paying a particular attention to the neutronic and photonic d…
Design and manufacturing feasibility of ITER TBM Frame and Dummy TBMs
2016
Abstract The operation and test of mock-ups of tritium breeding blankets relevant for a future commercial reactor is one of the goals of the ITER machine. To accomplish this goal, mock-ups of breeding blankets, called Test Blanket Modules (TBMs), are installed in three ITER equatorial ports. Each TBM and the associated shield form a TBM-set that is mechanically attached to a steel frame called TBM Frame. A Frame and two TBM-Sets form a TBM Port Plug (TBM PP). The ITER Organization is responsible for the design and manufacture of the TBM Frames and of the Dummy TBMs that could replace the TBM-sets in case they were not available. This paper describes the recent results of the design supporti…
Assessment of the Possible Lay-Out Influence on the HCLL-TBM Nuclear Response
2009
The Department of Nuclear Engineering of the University of Palermo (DIN) was involved, since several years, in the study of the nuclear response of the helium-cooled lithium lead (HCLL) test blanket module (TBM) which will be tested in ITER. In this framework a research campaign was performed, at the DIN, to asses the nuclear response of the TBM in a toroidal lay-out, with the specific aim to investigate the possible lay-out influence on the module nuclear behaviour by comparing the results obtained with those presented in a similar previous work focussed on the most recent design of the poloidal HCLL-TBM. A computational approach based on the Monte Carlo method was followed and a realistic…
On the influence of the supporting frame on the nuclear response of the Helium-Cooled Lithium Lead Test Blanket Module for ITER
2006
Abstract Within the European Fusion Technology Programme, very intense research activities have been promoted on the Helium-Cooled Lithium Lead (HCLL) breeding blanket concept with the specific aim of manufacturing a Test Blanket Module (TBM) to be irradiated in ITER. HCLL-TBM is foreseen to be located in an ITER equatorial port, being housed inside a proper steel-supporting frame. In particular, since that frame has been designed to provide two cavities separated by a dividing plate and HCLL-TBM is foreseen to fill just one of them, its nuclear response could vary accordingly to the filling status of the other one, unless the dividing plate is thick enough to isolate the components housed …